Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Fisher & Paykel specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 322-9727 Request a Repair
Error code · Wall Oven

Fisher & Paykel Oven Code F2: Cleaning Temperature Exceeded or Relay Transistor Problem

On Fisher & Paykel legacy 30-inch wall ovens such as the OS302, OD302, OS301, OD301 and the OB30DDEPX1, F2 means the oven temperature exceeded the maximum allowed during the clean cycle. On the OB24SDPX1, F2 means…

High · stop use, call now
Request a Repair(713) 322-9727
Code
F2
Appliance
Wall Oven
Brand
Fisher & Paykel
Warranty
30-day workmanship

What F2 means

On Fisher & Paykel legacy 30-inch wall ovens such as the OS302, OD302, OS301, OD301 and the OB30DDEPX1, F2 means the oven temperature exceeded the maximum allowed during the clean cycle. On the OB24SDPX1, F2 means something different: the transistor for relay 1 is in short circuit, or the supply voltage is below 150 volts. The display shows F2. Please check which of the two applies to your oven.

Common causes of F2

  • On the legacy 30-inch ovens, a clean cycle that ran hotter than allowed
  • A temperature sensor or control that misreads during cleaning
  • On the OB24SDPX1, a shorted relay 1 transistor
  • On the OB24SDPX1, supply voltage below 150 volts
✓ One safe check you can try

1. Switch the oven off and let it cool completely. 2. Check that the door is closed properly and vents are clear. 3. Reset the oven at the breaker for a minute. 4. Do not start another clean cycle if F2 appeared during one. 5. On the OB24SDPX1, note whether lights dim elsewhere, then call us.

! Why to stop there
  • The cause depends on the model, so confirming which oven you have matters.
  • A shorted transistor or low supply needs testing with a meter.
  • Overheating in a clean cycle should not be repeated until checked.
  • We give a written price first and a 30-day workmanship warranty after.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Wall Oven codes

F1 02Fisher & Paykel Oven Code F1 02: Clock Board Does Not Support Model ID F1 03Fisher & Paykel Oven Code F1 03: Clock Board General Software Error F1 04Fisher & Paykel Oven Code F1 04: Power Board Not Answering the Clock Board F1 11Fisher & Paykel Oven Code F1 11: Clock Board Critical Error F1 16Fisher & Paykel Oven Code F1 16: Clock Board Crystal Oscillator Error F2 01Fisher & Paykel Oven Code F2 01: Power Board Cannot Find Clock Board F2 02Fisher & Paykel Oven Code F2 02: Power Board Rejects Model ID F2 03Fisher & Paykel Oven Code F2 03: Power Board General Software Error
F2F2 questions
Why does F2 mean two things?

The legacy 30-inch ovens use F2 for over-temperature during cleaning. The OB24SDPX1, an Italian-built 24-inch oven, uses it for a relay 1 transistor short or low supply voltage.

Should I run self clean again?

Not until the oven is checked, especially if F2 appeared during a clean cycle. Another cycle may heat it past the limit again. Wait for us to check the sensor and relay first.

How do I tell which oven I have?

Check the rating label on the door frame or cavity edge. The model number begins OS, OD or OB, and the full number tells us which meaning applies.

Book a visit

Still seeing F2?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 322-9727
☎ Call the desk ▤ Request a Repair